Scholarships

Taraba State Polytechnic JAMB and Departmental Cut off Marks 2026/2027

Taraba State Polytechnic (TSP) JAMB and departmental cut-off marks to be used for the 2026/2027 academic session have been released. JAMB Cut-off marks for degree-awarding institutions is 180. See more details below.

TSP has announced 2026/2027 JAMB and departmental cut-off marks. JAMB UTME candidates will only require a minimum UTME score of 180 before you can offer Admission into the university. TSP JAMB Cut Off Mark and Departmental Cut Off Marks as released by the management for the 2026/2027 UTME admission exercise

Due to the high number of students wishing to study at the Taraba State Polytechnic (TSP), the admission process is competitive and admissions are given based on the higher the jamb scores, the higher the chances of being admitted.

TSP Cut -off Marks 2026.

Official TSP Cut-off Marks for 2026 is 180

Note: Meeting the minimum TSP cut off mark does not guarantee admission into your desired degree programme, your Post UTME Score, O’Level Grades, Subject Combination, JAMB Score and other factors are pre-requisite for admission to TSP.

READ ALSO:   Courses Offered In Moshood Abiola University of Science and Technology

TSP Departmental Cut Off Mark 2026

Taraba State Polytechnic TSP Departmental Cut Off Marks 2026/2027 has not been officially released. The following are just assumed points. Please always confirm from an official source.

TSP Faculty of Medical Sciences Cut Off Mark

Medicine – 250 and Above

TSP Faculty of Law Cut Off Mark

Law – 240 and above

TSP Faculty of Engineering Cut Off Mark

Mechanical, Chemical, Electrical, Civil, Computer, etc – 220 and above

TSP Faculty of Science Cut Off Mark

Industrial Chemistry, Industrial Physics, Computer Science, Geology, Microbiology, Biochemistry, Anatomy, etc – 190 and above

Please that TSP admission processes are competitive and admissions are given based on the higher the jamb scores, the higher the chances of being admitted.

READ ALSO:   Imo State Polytechnic, Umuagwo JAMB and Departmental Cut off Marks 2026/2027

If this post is helpful to you and you know that is going to be helpful to somebody else, please share it using the button below on Twitter, Facebook, Whatsapp or Email it to friends. There are buttons below for this (easy to use too)!

FAQs

1. What is the JAMB cut-off mark for Taraba State Polytechnic for the 2026/2027 academic session?

The JAMB cut-off mark for Taraba State Polytechnic for the 2026/2027 academic session is the minimum UTME score required for candidates to be considered for admission. Candidates should meet the institution’s stated minimum score and satisfy other admission requirements before applying for their chosen programme.

2. What is the departmental cut-off mark for Taraba State Polytechnic?

The departmental cut-off mark refers to the minimum score considered for admission into a particular course or programme. It may vary depending on the programme, number of applicants, available spaces and candidates’ performance. Meeting the general JAMB cut-off mark does not necessarily guarantee admission into every department.

READ ALSO:   School Fees: Federal College of Education (Technical) Asaba 2022/2023

3. Can I gain admission into Taraba State Polytechnic if my JAMB score is below the cut-off mark?

Generally, candidates whose UTME scores fall below the institution’s minimum requirement may not be eligible for admission through the regular UTME route. However, admission requirements can differ by programme and admission category, so candidates should confirm the specific requirements for their chosen course before proceeding.

4. How can I check Taraba State Polytechnic cut-off marks for 2026/2027?

Candidates should check the official Taraba State Polytechnic admission announcements and relevant JAMB information for the 2026/2027 session. The departmental requirements should also be confirmed before applying, especially where a course has additional requirements beyond the general institutional cut-off mark.

Leave a Reply

Back to top button